Advanced Service And Parts LLC [home link]
0
717.274.9396
English & Habla Español (Spanish)!


With the resurgence of Covid-19, you may experience some shipping delays. We are still shipping all parts we have in stock the same day, up until our cut-off time of 3:30 PM EST, but we cannot be responsible for the carrier's failure to deliver on time due to weather or Covid-19 related issues.
NOTICE: The shipping carriers UPS, FedEx, and USPS have suspended their service guarantees until further notice due to Covid-19. Please read more here.

TG410 TOUGH Series Digital Genset Control, DynaGen

$499.00  $435.50
Save: 13% off

1511
  • Part #: TG410-MP-CAN-MBI-G
  • 4 Units in Stock

    Tough Series - For engines or generators

    The TOUGH series controllers are designed to provide complete control, protection and engine instrumentation for both standard and electronic CAN Bus engines as well as metering for generator applications.

    All modules in this series are easily configured as either engine controllers or as generator controllers using either the front panel buttons or our PC configurator software.

    TOUGH series controllers are ideally suited for severe duty applications where reliability is critical such as mobile or stationary engine equipment and generators.

    The TG410 is the most advanced option in the TG Series, providing displays of Oil Pressure, Engine Temperature, Fuel Level, Oil Level, Engine Hours, RPM and Battery Voltage as well as J1939 Diagnostic Trouble Codes and a 150 Event Log.  Two customer-defined sensor parameters for temperature, pressure, voltage or levels can also be configured.  For generator applications, the TG410 provides a display of 1 or 3-Phase AC voltage, 1 or 3-Phase AC current, and frequency.  A Modbus communications port is standard on the TG410 model, allowing connection of a remote annunciator or an Internet gateway for remote management.

    Datasheet

    Accessories

    User Manual

    Wiring Configuration

    Software

    Firmware Updates

    Application Note

    Case Study

    Compliance Documents

    Accessories for the TG410:

    Are you using the relay pack? If so, order DWG1475 and RP100-VM. If you have a 24V battery system, just add (3) RLY0054 relays

    If you do NOT need the relay pack, you'll need harness DWG1476 instead

    For displaying AC volts or using the generator output to sense speed, use harness DWG1479

    If the engine is electronic (CANBUS/J1939 capable), or you're using a magnetic pickup for speed sensing or you're needing Modbus capabilities (such as a RA400 or Netbiter), use harness DWG1522

    To display AC Amps on the controller, use harness DWG1518 and order the Current Transformers (CT) below

    If you need more than 3 switched inputs and 3 switched outputs or 3 sensors, add harness DWG1477

    If wanting the enclosure order ENC0084 11.5x11.5x8.5" or ENC0080 8x8x4"

    For remote annunciation, use RA400-LS. The enclosure for it is not included, that would be ACC0109

    1/8" Oil pressure sender, order any of these two options, Click here

    1/8" Temp Sender order 02022-00, 1/4" order 02023-00, 3/8" order 02024-00, 1/2" order 02025-00

    Current Transformers:

    You will need to know the output Amps of the unit in order to chose the correct current transformers (CT) below. If you do not know the amps of the unit, here is how you can figure it out:

    Note: if your unit shows "KW" then multiply KW by 1000 to get Watts (KW x 1000 = Watts)

    For single Phase units: Watts / Volts = Amps    |    Order Qty (2)

    For three phase units: Watts / Volts / 1.73 = Amps    |    Order Qty (3)

    Round up to the nearest CT size

    50 amp CT,      75 amp CT,      100 amp CT,      150 amp CT,      200 amp CT,      300 amp CT,      400 amp CT,      500 amp CT,      600 amp CT,      800 amp CT,      1000 amp CT

    Optional Emergency Stop Button, order ACC87941

    For further help determining which harnesses you need, view our harness chart here.

     

  • Part #: TG410-MP-CAN-MBI-G
  • 4 Units in Stock
  • Manufactured by: Dynagen
Manufactured by: Dynagen Product ID: 1511 $499.00  $435.50
Save: 13% off
New


Items you may also be interested in... (Notice: This is an auto-generated list and these items may or may not fit your application. Use discretion / contact us if unsure.)

Snap-on RelayPak Option, Dynagen

Snap-on RelayPak Option, Dynagen
Snap-on RelayPak Option The RelayPak is socketed to accept four industry standard cube relays. When installed, the RelayPak (RP-100*) eliminates the need to mount and wire external slave relays for...
$45.54

DWG1479, 3-Phase AC Volts Harness (Gen or Mains)

DWG1479, 3-Phase AC Volts Harness (Gen or Mains)
4 foot May also be known as DWG1479R1.0
$15.89

Dynagen DWG1477, TG Advanced IO Harness

Dynagen DWG1477, TG Advanced IO Harness
 2 SW IN, 3 SW OUT, 1 Universal Sensor, 4'
$18.00

DWG1518, Harness, AC Current Sensing, TG Series

DWG1518, Harness, AC Current Sensing, TG Series
3 Phase AC Current Harness for the TG410 4'
$15.89

Dynagen DWG1522, 4' J1939 TG Mag/CANbus/Modbus

Dynagen DWG1522, 4' J1939 TG Mag/CANbus/Modbus
Mag / CANbus / Modbus Harness for the Dynagen TG Series, 4 foot  Note:  This harness comes with quantity 2) 120 Ohm loose resistors. However, we have an option that is easier to install, in...
$27.53


DWG1475, Main I/O Starter Harness for Relay Pack (3 SW IN, 3 SW

DWG1475, Main I/O Starter Harness for Relay Pack (3 SW IN, 3 SW
For applications that utlize the RP100-VM RelayPak option.   - 3 SW In - 3 SW OUT - 3 Sensors - Power - 4'
$27.53

24 Volt Relay (AZ9731C24DC3E) for TG and GSC Dynagen Controllers

24 Volt Relay (AZ9731C24DC3E) for TG and GSC Dynagen Controllers
You will need 3 of these to change your TG or GSC series controllers to 24 volt operation. 24V Cube Relay RLY0054 replaces:  Part # RLY0043 Part # AZ9731C24DC3E
$9.50

RA400-LS, Rmt Annun RA-400 for GSC400 and TG410

RA400-LS, Rmt Annun RA-400 for GSC400 and TG410
  Suggested Accessories: The enclosure will not be included, order ACC0109 If using with the TG410, order DWG1522 If using with the GSC400, order DWG1454R1.4 If powering the controller and...
$573.95

ACC0027 Temp Sender, Hi Temp, 1/8"NPT for Dynagen

ACC0027 Temp Sender, Hi Temp, 1/8"NPT for Dynagen
NPTF Temp Sender. 280F, 1/8" - 27 NPTF Fits all Dynagen controllers with digital display.  
$13.99

ENC0084, Enclosure, Dynagen TG Series 11.5x11.5x8.5"

ENC0084, Enclosure, Dynagen TG Series 11.5x11.5x8.5"
Enclosure does not include controller NEMA 1 Steel Encolsure with vibration mounts 11.5 x 11.5 x 8.5 inches
$158.05


Current Transformer 600:5 Amp, 2.5" ID

Current Transformer 600:5 Amp, 2.5" ID
CT Donut 2.5" ID, 600:5Amp If out stock, see other options  here Note:  Once this CT is out of stock, we will no longer be able to get this brand.
$39.95

ACC0109, Enclosure for RA-400

ACC0109, Enclosure for RA-400
8x8x4 Metal Enclosure for RA400
$56.94

ACC0120, 120VAC to 12VDC power adaptor

ACC0120, 120VAC to 12VDC power adaptor
This is a 120V AC to 12V DC power supply.  Suitable for powering the Dynagen RA400-LS .
$97.90

ACC0108-A, Oil Sender Replacement for Dynagen

ACC0108-A, Oil Sender Replacement for Dynagen
 Compatable with all Dynagen controllers that use an oil sender to display oil pressure on the digital panel ( GSC300, GSC400, TG350 & TG410).  Rated 0-100 psi. Suitable...
$44.05

DWG1478, Magnetic Pickup/J1939 Interface Harness

DWG1478, Magnetic Pickup/J1939 Interface Harness
If you are using this harness with J1939 application (eg. Engine ECM or electronic governor) or CANBUS, you will need to use 2) 120 OHm resistors:  one at the dynagen control and one at the...
$16.94


12V Starter Solenoid for Generac 56739, 056739, G056739

12V Starter Solenoid for Generac 56739, 056739, G056739
12 volt Starter Solenoid / relay for Generac generator and others.  Replaces Generac part # 70966, 56739 and 056739. Rated continuous duty.  Has silver plated contacts for longer life. This...
$42.68

Current Transformer 100:5 Amp CT

Current Transformer 100:5 Amp CT
CT, 100:5, 100A, 1.1inch ID
$28.95

ENC0080, Enclosure, Dynagen TG Series 8x8x4"

ENC0080, Enclosure, Dynagen TG Series 8x8x4"
NEMA 1 Steel Encolsure with vibration mounts
$104.83


ACC0108 Oil Sender for Dynagen GSC300, GSC400, TG350 & TG410

ACC0108 Oil Sender for Dynagen GSC300, GSC400, TG350 & TG410
We are now substituting this part to the ACC0108-A which has the same specs.  This may no longer be readily available on the shelf.  If you still require this part, there will be a lead...
$84.95

Current Transformer 300:5 Amp, 1.1" ID

Current Transformer 300:5 Amp, 1.1" ID
If out of stock, see other options here Note:  Once this CT is gone, we will no longer be able to get this brand again. CT Donut 1.1" ID, 300:5Amp 
$24.95

Dynagen ACC0046, Current Transformer 200:5 Amp

Dynagen ACC0046, Current Transformer 200:5 Amp
Dynagen 200A:5A Current Transformer Can replace # 2RL201 If out of stock see other options here
$31.77

Dynagen ACC0154 PCA Resistor package CAN J1939 connection

Dynagen ACC0154 PCA Resistor package CAN J1939 connection
Dynagen ACC0154 PCA Resistor package CAN J1939 connection Note:  You will typically need 2 of these - one at the Dynagen control and one at the terminating end of your harness.  The...
$16.00


TG350 TOUGH Series Digital Genset Control, Dynagen

TG350 TOUGH Series Digital Genset Control, Dynagen
Tough Series - For engines or generators The TOUGH Series® controllers are designed to provide complete control, protection, and engine instrumentation for both standard and electronic CAN Bus...
$389.00  $338.14
Save: 13% off

Dynagen ACC0099, Temp. Sender, Datcon 02025-00, 1/2"NPT

Dynagen ACC0099, Temp. Sender, Datcon 02025-00, 1/2"NPT
Dynagen ACC0099 / Datcon 02025-00, Temperature Sender Specs:  140-320 degrees F, 1/2 " National Pipe Threads 
$23.98

Excercise Timer, Milbank Z1157711 / DynaGen ACC0073, 120V

Excercise Timer, Milbank Z1157711 / DynaGen ACC0073, 120V
This exercise clock is powered by 110 - 120VAC, and replaces the timers following exactly: DynaGen ACC0073 Milbank Z1157711 or 1157711 Ronk ELCO6130S Can be used for any application that needs a...
$108.32


RLY0053, 12VDC Relay for TG and GSC Dynagen Controllers

RLY0053, 12VDC Relay for TG and GSC Dynagen Controllers
Relay, 12VDC, Hasco for Dynagen You will need 3 of these to change your TG or GSC series controllers to 12 volt operation.
$9.50

323-416, Temp Sender for Dynagen

323-416, Temp Sender for Dynagen
Sender, Temp, M14x1.5, 250F
$23.66

323-420, Temp Sender for Dynagen

323-420, Temp Sender for Dynagen
Temp Sender 250F, 1/4 NPT VDO
$16.95

Rheostat for Voltage regulator, 1k ohm, 1 watt POT

Rheostat for Voltage regulator, 1k ohm, 1 watt POT
This 1k (1000 ohms) 1 watt pot is for remote adjustment of several AVR's that we sell.  It is not required, but is primarily used for mobile or rental generators used for different...
$15.95

Dynagen DWG1476, TG Main I/O Starter Harness

Dynagen DWG1476, TG Main I/O Starter Harness
To be used in applications  not  utlizing the RP100-VM RelayPak option. 3 SW IN, 3 SW OUT, 3 Sensors - 4'
$24.36


E000-23412/1P (MX341) OEM Stamford Voltage Regulator

E000-23412/1P (MX341) OEM Stamford Voltage Regulator
This is a new Genuine Stamford MX341 AVR. Replaces: E000-23412/1P E000-23412 E000-23410  MX341 (All earlier versions) MX341 2 MX341-2 Dealers & volume users contact us for even lower...
$494.20

MX341-A, Regulator

MX341-A, Regulator
Regulator, MX341 Replacement
$249.00

ACC87941 E-Stop, 20A 2 N/C Contacts

ACC87941 E-Stop, 20A 2 N/C Contacts
Emergency Stop button, 20 Amp, 2 N/C Contacts 
$67.18

Current Transformer 400:5 Amp CT

Current Transformer 400:5 Amp CT
CT, 400:5 Donut with 1.5" Hole Replaces these parts:  2RL401 - 1.1 ID, 400:5 5RL401 - 1.5 ID, 400:5 7RL401 - 2.5 ID, 400:5
$39.95

Dynagen ACC0045, Current Transformer 100:5 Amp

Dynagen ACC0045, Current Transformer 100:5 Amp
Current Transformer, 10KV, 100A:5A If out of stock see other options here
$39.12


ACC87943 E-Stop, 20A 1 NC + 1 NO

ACC87943 E-Stop, 20A 1 NC + 1 NO
Universal Emergency Stop button, 20A 1 NC + 1 NO
$59.95

02067-00, Sender for Dynagen

02067-00, Sender for Dynagen
M16x1.5 100-280,140-320
$18.95

CT Donut 2.5" 500:5

CT Donut 2.5" 500:5
500A:5A Current Transformer 2.5" Opening in the center   This item is no longer available, please see other options here
$39.95

Dynagen ACC0048, Current Transformer 500:5 Amp

Dynagen ACC0048, Current Transformer 500:5 Amp
Dynagen 500A:5A Current Transformer Has approx 1.1" opening in the center.  If out of stock, see other options here
$32.83


Hotstart TPS051GT8-000 Block Heater: 80-100 degrees

Hotstart TPS051GT8-000 Block Heater: 80-100 degrees
Compact 500 watt, 120 volt Tank Heater with 80-100 degree thermostat - High Impact Plastic. Ideal coolant heater for propane or natural gas Generator sets. OEM type heater used on Olympian, CAT,...
$178.89  $119.95
Save: 33% off

Current Transformer 800:5 Amp with 2.88" Hole

Current Transformer 800:5 Amp with 2.88" Hole
CTC800L48 - 800:5 Amp CT / Donut with 2.88" Hole
$47.95

3034572-A 5/8" Mag Pickup, Cummins Type

3034572-A 5/8" Mag Pickup, Cummins Type
Replacement 5/8" Mag Pickup for Cummins 3034572
$44.95

Replacement MX321 Regulator for Stamford E000-23212

Replacement MX321 Regulator for Stamford E000-23212
After-market Regulator for Stamford / Newage.
$329.00

Governor Speed Control for Barber Colman, Woodward, Cummins

Governor Speed Control for Barber Colman, Woodward, Cummins
Our model ESC2301-A universal 15 amp electronic governor controller replaces many part numbers for Barber Colman, Woodward, Cummins, Onan, and many others!  This design works on 12V OR 24V...
$279.00  $199.00
Save: 29% off


Copyright © 2021 Advanced Service And Parts LLC (A.S.A.P). Powered by Zen Cart | Custom Zen Cart work by ZenExpert