Dynagen Controls

M16x1.5 100-280,140-320 more info

These heavy-duty 12VDC relays must be installed in the Dynagen ES51 or ES52 series engine controller for 12V DC engines or generators.  This is Dynagen Accessory # RLY0013. more info

These heavy-duty 24VDC relays must be installed in the Dynagen ES51 or ES52 series engine controller for 24V DC engines or generators.  This is Dynagen Accessory # RLY0017. 24V Mini Cube Relay... more info

You will need 3 of these to change your TG or GSC series controllers to 24 volt operation. 24V Cube Relay RLY0054 replaces:  Part # RLY0043 Part # AZ9731C24DC3E more info

NPTF Temp Sender. 280F, 1/8" - 27 NPTF Fits all Dynagen controllers with digital display.   more info

We are now substituting this part to the ACC0108-A which has the same specs.  This may no longer be readily available on the shelf.  If you still require this part, there will be a lead... more info

8x8x4 Metal Enclosure for RA400 more info

This is a 120V AC to 12V DC power supply.  Suitable for powering the Dynagen RA400-LS . more info

This power supply works on 110V - 240VAC with a 12V DC output.  Suitable for powering the Dynagen  RA400-LS .  Can also be used as a universal 12VDC power supply. more info

ACCADAPTDGC-TG, Adapter plate for Dynagen TG Series This steel adapter plate, painted black, was designed to allow mounting the Dynagen TG Series controllers onto existing enclosures... more info

8ft Harness Starter Kit (AC Current Sensing, Digital Input, and Analog Input Cables) for the GSC400 more info

5' pigtail harness for Modbus connection for the GSC400 Click here for wiring diagram. Please note before ordering this part:  The GSC400 has been in production for approximately 13... more info

For applications that utlize the RP100-VM RelayPak option.   - 3 SW In - 3 SW OUT - 3 Sensors - Power - 4' more info

If you are using this harness with J1939 application (eg. Engine ECM or electronic governor) or CANBUS, you will need to use 2) 120 OHm resistors:  one at the dynagen control and one at the... more info

4 foot May also be known as DWG1479R1.0 more info

3 Phase AC Current Harness for the TG410 4' more info

DWG1565, TG/TE Pro J1 Harness, Dynagen;  Fully populated J1 Harness, all I/O present. more info

Dynagen DWG1576 Harness for TL3600 TOUGH Link 2 foot Harness with Mating connector to 6 PIN Deutsch Connector DT04-6P more info

Current Transformer, 10KV, 100A:5A If out of stock see other options here more info

Dynagen 200A:5A Current Transformer Can replace # 2RL201 If out of stock see other options here more info

Dynagen 300A:5A Current Transformer If out of stock, see other options here more info

Dynagen 500A:5A Current Transformer Has approx 1.1" opening in the center.  If out of stock, see other options here more info

Dynagen 600A:5A Current Transformer If out of stock, see options options here more info

Dynagen CT, 1000A:5A, 1.5" Hole more info

Dynagen ACC0099 / Datcon 02025-00, Temperature Sender Specs:  140-320 degrees F, 1/2 " National Pipe Threads  more info

Dynagen ACC0154 PCA Resistor package CAN J1939 connection Note:  You will typically need 2 of these - one at the Dynagen control and one at the terminating end of your harness.  The... more info

5' CANbus harness for the GSC400 Click here for wiring diagram. more info

5' SW Output Harness for the GSC400 Click here for wiring diagram. more info

Extra Pre-Crimped Wires Package of 5 5 foot length more info

To be used in applications  not  utlizing the RP100-VM RelayPak option. 3 SW IN, 3 SW OUT, 3 Sensors - 4' more info

 2 SW IN, 3 SW OUT, 1 Universal Sensor, 4' more info

Mag / CANbus / Modbus Harness for the Dynagen TG Series, 4 foot  Note:  This harness comes with quantity 2) 120 Ohm loose resistors. However, we have an option that is easier to install, in... more info