Advanced Service And Parts LLC [home link]
0
1.800.630.1230
English & Espaol (Spanish)!

Generac 0F97190SRV Voltage Regulator, was 0F9719, 083049

$143.31  $115.26
Save: 20% off

875
  • Part #: 0F97190SRV
  • 7 Units in Stock

    Generac / Guardian Voltage Regulator - usually marked F9719 on part. Has (6) 1/4" spade terminals for wire connections.

    Replaces the following part numbers:

    • 81918
    • 83049
    • 083049
    • 0830490SRV
    • 83049GS
    • SRV83049
    • F9719
    • 0F9719
    • 0F97190SRV

    The 83049 series AVR has been discontinued by Generac / Guardian, and replaced with 0F97190SRV.  It looks virtually identical and works the same at a lower cost!

    A.C.Voltage Regulator

    Used in all current production R.V. products except variable speed units. Also used on air cooled Home Stand-by units. 0F9719, 083049 and 083048 are virtually the same, except the 083048 has no cooling fins on the back of the regulator. These regulators can be interchanged, but the 083049 and 0F9719 are thicker due to the cooling fins and will require longer bolts to replace an 083048.

    IMPORTANT:

    After installing the new voltage regulator, determine if the frequency is correct. Set mechanical governors to 62Hz at no load. Electronic governors set to 60Hz no load. After determining that the hertz are correct, measure the AC output. The voltage should be 124VAC at 62Hz with no load or 120VAC at 60Hz with no load.  If the voltage is either high or low, adjust the brass screw in blue trim potentiometer next to the red LED to the correct voltage.

  • Part #: 0F97190SRV
  • 7 Units in Stock
  • Manufactured by: Generac®
Manufactured by: Generac® Product ID: 875 $143.31  $115.26
Save: 20% off
New



You might also like...

Generac 098647ASRV (98647) Governor Control Kit, Stepper

Generac 098647ASRV (98647) Governor Control Kit, Stepper
Generac 098647ASRV Electronic Governor "Speed Control Kit" is the latest revision control for the Governor Stepper Motor. Includes Controller, Wiring Harness, and Instructions.  May...
$185.43

Generac 65795 Rectifier, Battery Charge (Briggs 65795GS)

Generac 65795 Rectifier, Battery Charge (Briggs 65795GS)
Generac / Guardian 065795 Battery Charge Rectifier ~ same as Briggs & Stratton 65795GS
$11.54

Engine Control replacement for 300-2604 ONAN®

Engine Control replacement for 300-2604 ONAN®
New aftermarket PCB Control monitor is a direct replacement for ONAN® 300-2604. Our part # is 3002604-A
$197.70

Cummins 212-1303 Brush Block Assy. for Onan

Cummins 212-1303 Brush Block Assy. for Onan
Brush Block Assy., 212-1303, Onan NOTE:  This brush holder includes qty 2 brushes.  This holder is NOT for the BGE/NHE Emerald models.  Contact us with your full model number if...
$37.17

Generac Brushes and Holder - Was 66386, 066386

Generac Brushes and Holder - Was 66386, 066386
Generac (Guardian) brush assembly includes holder, brushes, & springs.  1/4" spade quick connect terminals on top. Now comes with instructions. Replaces: 66386 066386 0663860SRV
$14.02


P/N 69341-A Pre-Cleaner for Generac

P/N 69341-A Pre-Cleaner for Generac
Aftermarket equal element for Generac # 069341 and 69341 . (This is a Pre-Cleaner for Generac Air Filter p/n 73123 and 073123)
$5.50

0A18010SRV GENERAC BATTERY CHARGER A1801

0A18010SRV GENERAC BATTERY CHARGER A1801
GENERAC / GUARDIAN 0A18010SRV 12 volt ENGINE BATTERY CHARGER. Replaces A1801, 0A1801
$152.84  $152.04
Save: 1% off

Generac 0D86150SRV Control Board replaces C6211, 0D8615

Generac 0D86150SRV Control Board replaces C6211, 0D8615
New Generac 0D86150SRV controller! Fits Guardian Home Standby generators. Replaces the following Generac part numbers: C6211 0C6211 0C6211ASRV 0C62110SRV 0D86150SRV 0D8615ASRV 0D8615 D8615 ...
$338.00  $264.43
Save: 22% off

Generac 0D9235BSRV Oil Switch replaces 0D9235A

Generac 0D9235BSRV Oil Switch replaces 0D9235A
  The 0D9235BSRV is a heavy-duty oil switch. Also replaces Generac 0D9235A, 0D9235 & D9235. Comes with instructions and a jumper wire to ground switch. Quality unit made for Generac by...
$31.88

092234 / 0922340SRV Generac Generator Control Board

092234 / 0922340SRV Generac Generator Control Board
Genuine Generac / Guardian RV generator control board for most late model sets. The part #92234  is usually marked in white ink on the side as shown on picture. Replaces the following part...
$206.46  $170.68
Save: 17% off


Generac Start / Stop Switch 87798

Generac Start / Stop Switch 87798
GENERAC PART 087798 SWITCH (Miniature 6A SPDT) Used primarily on newer Guardian / Generac RV generators to start & stop the generator on the control panel. Momentary spring loaded action returns...
$3.76

Generac 0936420SRV (70325) / Quicksilver # 810658 Control Board

Generac 0936420SRV (70325) / Quicksilver # 810658 Control Board
Description: Generac & Guardian RV & Quicksilver Marine Control Board (New genuine part) Replaces Part numbers: 93642 093642 0936420SRV SRV93642 70325 70325G 810658 (Quick silver part...
$366.92  $300.17
Save: 18% off

Generac 0D4409 Governor / Idle Control for Guardian Portable

Generac 0D4409 Governor / Idle Control for Guardian Portable
This is a genuine Generac / Guardian 0D4409 stepper motor control.   Formerly part # 0D44090SRV. Note: What appears to be a part # on top of the module is actually just the # of the internal...
$203.95

Generac 0G58840SRV replaces 0F89920SRV

Generac 0G58840SRV replaces 0F89920SRV
 Generac PCB ASSY, MODIFIED 0F8992.  This is the newest revision that replaces Generac / Guardian part # 0F8992 and 0F89920SRV. 0F89920SRV is no longer available.
$253.58

Quicksilver 88-810126 Breaker, 5 A / Generac 048512, 46-500-P

Quicksilver 88-810126 Breaker, 5 A / Generac 048512, 46-500-P
This Generac # 48512 is a 5 amp auto reset circuit breaker that protects the model 083048 or 083049 voltage regulator / DPE stator winding on the Quick silver generators and some Generac RV...
$64.56


0A8584 Oil Switch, Generac

0A8584 Oil Switch, Generac
Generac Oil Pressure Switch replaces earlier # A8584
$21.03

Leroy Somer R250 Replacement AVR Voltage Regulator

Leroy Somer R250 Replacement AVR Voltage Regulator
 This is an aftermarket replacement for leroy somer R250.
$229.00  $169.00
Save: 26% off

Choke Module, Generac 073601, Quicksilver 810677

Choke Module, Generac 073601, Quicksilver 810677
Generac  Choke Module 73601,  - same as Quicksilver 810677. Fits some older Generac RV models, and Quicksilver marine generators.
$53.09

239247 Brush Holder, Kohler

239247 Brush Holder, Kohler
239247 Brush Holder, Kohler
$28.81

Resistor, 300 watt 10 ohms, with mounting bracket

Resistor, 300 watt 10 ohms, with mounting bracket
This large wirewound ceramic resistor is great for using in series with an exciter field that is both low voltage and low resistance.  Most voltage regulators will not stabilize when...
$49.95


Universal Voltage Regulator VR9040

Universal Voltage Regulator VR9040
Click here for manual.   The  V R9040   universal 40 amp  voltage regulator is an electronic A VR  which lets the alternator   produce a fixed  AC  output...
$369.00

Regulator for Powermate 0067314, 0063290, 0063291, some Honda

Regulator for Powermate 0067314, 0063290, 0063291, some Honda
New LOWER PRICE!  Replacement Voltage regulator for Coleman Powermate 0067314 / 0063290 /  0063291 / 0063948 / 0064525 for portable generators and others.  Your original AVR...
$44.99  $37.95
Save: 16% off

Replacement AVR Cat VR6, Basler AVC63-12B1, Caterpillar VR3, VR4

Replacement AVR Cat VR6, Basler AVC63-12B1, Caterpillar VR3, VR4
Quality After-market AVR Replaces: Caterpillar model VR6 (part # 365-2076)  Cat VR3 and Cat VR4 (Now obsolete and replaced by VR6) Leroy Somer 202-8634 or 2028634 Basler AVC63-12B1 *KATO...
$399.00

Generac G090144 Circuit Breaker, 20 Amp (090144, 90144)

Generac G090144 Circuit Breaker, 20 Amp (090144, 90144)
Generac 20 amp single pole Circuit Breaker made by Carlingswitch. Fits some Generac / Guardian RV generators, etc.
$25.08

Generac 0C8127 / C8127 Air Filter, Genuine

Generac 0C8127 / C8127 Air Filter, Genuine
Genuine Generac / Guardian 0C8127 air filter fits many V-Twin GT990, GT760 engines.  
$14.85  $12.16
Save: 18% off


Carburetor, Generac 0D8332

Carburetor, Generac 0D8332
This carb is for Generac model # 04700-0 Gasket 078631 carb to manifold Gasket 0D8372 carb to airbox
$63.96

Generac 73123-A / 073123-A Air Filter

Generac 73123-A / 073123-A Air Filter
P/N 073123-A Air filter element fits some Generac RV generators with air-cooled V-Twin engines. (Primarily GN480 and GN570) Recommended: P/N 69341-A Pre-Cleaner for Generac Aftermarket equal for...
$13.95

(70185) Oil Filter for Generac

(70185) Oil Filter for Generac
Genuine Generac / Guardian Oil Filter 070185D. -  May also be labeled 70185 or 070185B.*  NOTE: Some newer versions are painted orange, but we send  the latest revision. For even more...
$8.60  $7.23
Save: 16% off

Generac Primer Rocker Switch 92113

Generac Primer Rocker Switch 92113
Generac # 092113 / 92113 momentary rocker switch. Used as a "fuel primer switch" on many Generac Guardian RV generators. Switch springs back to "OFF" when released.
$4.02


Generac 053623 2.5 Amp Breaker 2-6500-P10 or 46-500-P

Generac 053623 2.5 Amp Breaker 2-6500-P10 or 46-500-P
Generac # 53623 circuit breaker now sold as p/n 053623 . Auto reset, 2.5 amp circuit breaker. Used to protect AC power input to Generac voltage regulators # 83048 or 83049 in some models. Check for...
$40.87

077005H Rotor, Generac RV Replaces 77005 and 77005G

077005H Rotor, Generac RV Replaces 77005 and 77005G
Generac 77005H Rotor for RV generator.  Replaces 77005 and 77005G

New AVR for Stamford SX460, E000-24600 & Onan 305-0982

New AVR for Stamford SX460, E000-24600 & Onan 305-0982
Also replaces obsolete Stamford Newage Series 6 E000-26000 and 450-13900.  This is an exact replacement Voltage Regulator for the following: Stamford Newage SX460 E000-24600 E000-24602 Cummins...
$169.00  $109.00
Save: 36% off

Generac 91848 Gasket for Oil Filter Adapter on GH220 & GN220

Generac 91848 Gasket for Oil Filter Adapter on GH220 & GN220
Generac 91848 / 091848 Gasket for # D8778 oil filter adapter.
$7.88

Generac Relay 063617 with Flange Mount, 12VDC

Generac Relay 063617 with Flange Mount, 12VDC
Generac Relay # 63617 also marked TYCO / Potter & Brumfield KUP-11D55-12. Coil rated 12VDC. DPDT contacts. (2 pole double throw). Has (2) rows of (4) .187" spade terminals. Used in small...
$19.90


075216 Generac Polygroove Belt for RV Generator

075216 Generac Polygroove Belt for RV Generator
GENERAC PART 075216 / 75216 BELT,V-RIB Other part numbers: GEN-075216
$26.01

Generac 75207 Circuit Breaker, 20 Amp Pop - out type

Generac 75207 Circuit Breaker, 20 Amp Pop - out type
Generac 75207 Circuit breaker used on portable generators, etc. Has 1/4" Q.C. terminals on the back. Same as 75207GS and 075207
$5.33

Generac 75207A Circuit Breaker, 30 Amp Pop - out type

Generac 75207A Circuit Breaker, 30 Amp Pop - out type
Generac 75207A Circuit breaker used on portable generators, etc. Has 1/4" Q.C. terminals on the back. Same as 75207A GS and 075207A NOTE: These are usually a stock item, but occasionally need...
$4.06

Generac 0A4600 Carburetor, Generac GN360 & GN410 replaces 91187A

Generac 0A4600 Carburetor, Generac GN360 & GN410 replaces 91187A
P/N A4600 Carburetor, Genuine, New Generac replaces 91187A and 091187A. Fits GN360 or GH360 (13HP) & GN410 or GH410 (14 or 15HP) Generac engines. NOTICE: Does not come with gaskets. If you...
$66.91


Generac 076009ASRV (76009A) Control Board - New!

Generac 076009ASRV (76009A) Control Board - New!
Genuine new Generac part # 076009ASRV Fits many water-cooled Generac, Guardian & CENTURION branded generators with an "all-in-one" PC board that controls both the generator and the...
$372.71  $331.79
Save: 11% off

032300 Fuse Holder, Generac - (Was 32300)

032300 Fuse Holder, Generac - (Was 32300)
Generac Fuse Holder replaces 32300 This is the common fuse holder for many of the Generac RV generators with the 7.5A or 15A fuses. May fit some other applications as well.
$5.19

New Delco type Starter for Generac 0E4271, 0E42710SRV

New Delco type Starter for Generac 0E4271, 0E42710SRV
This one looks just like the genuine Generac 0E4271, 0E42710SRV (Delco brand). Do not buy the aftermarket ones that look like the larger 0C3017 with the bigger gear, and supported by a bracket at the...
$79.95

Generac 0F5022 Solenoid Coil for Regulator (was C5765)

Generac 0F5022 Solenoid Coil for Regulator (was C5765)
Generac / Guardian 0F5022 replacement 12 volt solenoid coil for gas regulators replaces Generac # (C5765).  Used on the following models of standby generator sets: 4389 4390 4456 4758...
$27.06

Fuel Pump for Generac 90475, 77663, Onan & Kohler GM39462

Fuel Pump for Generac 90475, 77663, Onan & Kohler GM39462
IMPORTANT NOTICE: You are responsible for the application and proper installation of this pump! Gasoline is very flammable and the fumes are explosive! Information below is for reference purposes...
$133.95  $81.95
Save: 39% off


Spark Plug - Generac P/N E7585 or 0E7585

Spark Plug - Generac P/N E7585 or 0E7585
Spark Plug - Generac P/N 0E7585 (Champion RC14YC - Pre-gapped at approx. 0.030" ) BUY TWO for GT990 and other twin cylinder engines. NOTE: GENERAC HAS REVISED THEIR RECOMMENDATIONS FOR SOME...
$3.74

Generac 070185ES Oil Filter, replaces 070185E, 070185F

Generac 070185ES Oil Filter, replaces 070185E, 070185F
Heavy duty version of the Generac Guardian 70185, 70185B and 70185D oil filter.  30% more capacity!  15mm longer than the 70185D. (less than 3/4" longer)  Primary use is on the...
$9.51

Generac # 54502 3 Amp Breaker 2-6500-P10 or 46-500-P

Generac # 54502 3 Amp Breaker 2-6500-P10 or 46-500-P
Generac # 054502 circuit breaker, auto reset, 3 amp. Used for AC power feed to Generac voltage regulators # 83048 or 83049 in some models. Check for part # 2-6500-P10 or 46-500-P written on the...
$49.63

Brush for ONAN 214-0103 and A053W559 - RV Genset

Brush for ONAN 214-0103 and A053W559 - RV Genset
These replacement brushes are in stock!   The Genuine Onan 214-0103 brushes are no longer available as the same #.  We are offering these after-market equal replacements from a company...
$8.49  $7.29
Save: 14% off

Gasket # 078631 (carb to manifold) fits C1535A & 98469 carb

Gasket # 078631 (carb to manifold) fits C1535A & 98469 carb
Generac mounting gasket #078631 (old # 78631) fits between carburetor and intake manifold of Generac GN190, GN191, GN220 Generac air-cooled engines. Fits C1535A and 98469 carburetors.
$2.96


Copyright © 2019 Advanced Service And Parts LLC (A.S.A.P). Powered by Zen Cart | Custom Zen Cart work by ZenExpert